RMI_DATASET_QPE
Royal Meteorological Institute of Belgium
Institut Royal Météorologique de Belgique
Koninklijk Meteorologisch Instituut van België
Königliche Meteorologische Institut
info@meteo.be
http://www.meteo.be
WWW:LINK-1.0-http--link
2023-02-28
EPSG:4258
Belgian surface rainfall rate and accumulation estimation
2023-02-28
qpe
RMI-be
RADQPE provides high resolution radar-based quantitative precipitation estimation in realtime for Belgium and its surroundings.
This product is not publically available yet.
Royal Meteorological Institute of Belgium
Institut Royal Météorologique de Belgique
Koninklijk Meteorologisch Instituut van België
Königliche Meteorologische Institut
info@meteo.be
Royal Meteorological Institute of Belgium
Institut Royal Météorologique de Belgique
Koninklijk Meteorologisch Instituut van België
Königliche Meteorologische Institut
info@meteo.be
P0Y0M0DT0H5M0S
https://opendata.meteo.be/graphics/qpe.png
Atmospheric conditions
Atmosferische omstandigheden
Conditions atmosphériques
Atmosphärische Bedingungen
GEMET - INSPIRE themes, version 1.0
2008-06-01
federal government
radar
observation
rainfall
National
Nationaal
National
National
Spatial scope
2019-05-22
No limitations on public access
Geen beperkingen op openbare toegang
Pas de restrictions concernant l'accès public
Öffentliche Zugang nicht beschränkt
1000
climatologyMeteorologyAtmosphere
0.55
9.396
47.25
53.41
2018-05-01T00:00:00
HDF
5
https://opendata.meteo.be
WWW:LINK-1.0-http--link
RMI opendata portal
Portail opendata de l'IRM
dataset
INSPIRE Conformity
Commission Regulation (EU) No 1089/2010 of 23 November 2010 implementing Directive 2007/2/EC of the European Parliament and of the Council as regards interoperability of spatial data sets and services
2010-12-08
See the referenced specification
false
The RADQPE product is obtained after a careful processing of the weather radar measurements and a merging with rain gauge measurements. The scientific basis can be found in Goudenhoofdt and Delobbe (2016). There is a continuous improvement process based on research and quality control.
WEATHER RADAR MEASUREMENTS
Radars emit electromagnetic pulses, typically with a length of 500m and a width of 1 degree. Part of the energy of this pulse is reflected back to the radar by precipitation. Radars performs scans at different elevations in about 5 minutes. Estimating rainfall from radar measurements is a challenge because of the many sources of error and uncertainty.
RADQPE is based on the 3D reflectivity measurements of the following radars:
- Avesnois, France, French National Meteorological Service
- Helchteren, Belgium, Flanders Environment Agency
- Jabbeke, Belgium, The Royal Meteorological Institute of Belgium
- Neuheilenbach, Germany, German National Meteorological Service
- Wideumont, Belgium, The Royal Meteorological Institute of Belgium
These radars exhibit various technology, scanning strategy and data processing. They use Doppler capabilities to remove non-meteorological echoes with zero velocity (e.g. hills). Some processing can lead to loss of information and make further processing difficult.
RAIN GAUGE MEASUREMENTS
The following automatic rain gauge networks are used by RADQPE:
- 91 weighted gauge OTT2, SPWMI, Belgium
- 42 weighted gauge OTT2, VMM, Belgium
- 19 weighted gauge OTT2, WL, Belgium
The quality control by data providers is void (WL), limited (SPW) or unknown (VMM). No extra quality control is performed before writing the data in the RMIB database.
QUALITY CONTROL OF THE RADAR MEASUREMENTS
- Identification of permanently contaminated measurements (hills, wind farms, interference).
- Correction for radar beam blockage by terrain
- Identification of clutter (i.e. non-meteorological echoes or signals) based on satellite cloudiness products
- Identification of clutter based on vertical profiles of radar reflectivity
- Identification of clutter based on image texture
- Identification of clutter based on dual-polarisation technology (only Helchteren and Jabekke)
FROM RADAR MEASUREMENTS TO GROUND RAINFALL RATE ESTIMATION
1. Identification of convective precipitation
2. Extrapolation to ground of non convective precipitation using an averaged vertical profile of reflectivity
3. Interpolation of missing data (vertically then horizontally)
4. Conversion of reflectivity into rain rates based on precipitation type (hail, convective, stratiform)
SINGLE RADAR ACCUMULATION AND BIAS CORRECTION
1. The movement of precipitation between 5-min snapshots is obtained using optical flow methods. It is used to accumulate rain rates over the past 1 hour and 24 hours.
2. The accumulations are adjusted by a mean field bias (MFB), which is computed based on the rain gauges measurements corresponding to the same duration
3. To remove radar calibration difference before compositing, the single radar rain rates are adjusted by the median of the 24h biases (computed at the previous step) for the past month.
COMPOSITING, ACCUMULATION AND RADAR-GAUGE MERGING
1. For the months with dominant convective precipitation (May, June, July, August), the single radar rain rates are combined into a composite by taking the maximum value of the 3 closest radars.
2. For other months, the composite is based on all values weighted based on the distance to the radar.
3. Rainfall accumulation of the composite rain rates are made for the past 5 minutes, 10 minutes, 1 hour and 24 hours.
4. The 1h and 24h composite accumulations are adjusted by the MFB correction
5. The 1h bias correction of the previous step is applied to the composite rain rate. The correction is also applied to the 5 and 10-min composite accumulations